Safelease
Mould Release Emulsion
Developed using the latest water soluble polymer technology, to produce an environmentally friendly and highly effective mould release agent for general site use.
A low odour, low VOC, non-staining mould release agent designed with minimum blowhole formation and providing a sharp, uniform and non-stained concrete surface.
It is particularly suited for white or fair faced concrete finishes.
| Size (available in) |
|
|---|---|
| Coverage | 30-40m2 per litre |
| Certified |
|
- Description
- Additional information
- Enquiry form
Description
Datasheet details
Date of issue: 01/02/2025
Tech Data Sheet No.: 557
Revision No.: v2
Download Safelease Data Sheet 2025
Request Safety Sheet
SAFELEASE has been developed using the latest water soluble polymer technology to produce an environmentally friendly and highly efficient release material for concrete formwork on site. SAFELEASE is ready to use and particularly suited to outdoor use on faced sealed plywood, steel moulds and other impervious formwork materials.
• Recommended for high quality finishes
• WRAS approved product
• Low to no odour
• Safe, environmentally friendly product.
• NO VOC content
• Low viscosity for easy application
• Readily biodegradable
• After water evaporation, film is resistant to water wash off
• Forms may be stripped early when other factors permit.
• Suitable for use with white, coloured or standard OPC concrete finishes.
• Non-staining
• Fully compatible with the subsequent application of silicone or similar surface treatments when used as recommended.
Apply thinly, by spray, brush or swab prior to each concrete pour. Application should be a minimum of 1 hour before pouring, for the excess water to evaporate off and the release film to be properly established. With first application to new formwork a second light coat may be required.
On vertical forms any excess material accumulating at the bottom of the form should be removed. On untreated timber surfaces additional coats may be required for first use.
A thin coating is recommended giving a coverage between 30 to 40m2 per litre depending upon surface porosity and texture. Protect from rain when still wet.
SAFELEASE is a water based product and should be protected from frost. Containers must be kept sealed after use. The product may require mild agitation before use if stored for more than 6 months.
In excess of 12 months in sealed containers, use within 2 months of opening. Roll or agitate prior to use.
Safelease mould release agent is manufactured by Adomast Manufacturing Ltd and shall be applied strictly in accordance with the manufacturer’s instructions. For specific advice regarding any aspect of this product please consult our Technical Department.
Prolonged physical contact should be avoided and personal and environmental hygiene encouraged in common with the use of all chemical products. Where contact with skin occurs, the material should be removed with soap and water. If splashes affect eyes, they should be bathed immediately with clean water and if discomfort persists medical attention should be sought.
See Safety Data Sheet for further information.
Product in action, Case Study – Forth Road Bridge
With the announcement that a new bridge was to be built across the Firth of Forth in Edinburgh, Adomast was contacted by local contractors to supply construction chemicals into the project. Given the location of the construction work it is imperative that the chemicals used did not harm the flora and fauna in the vicinity. Therefore Adomast offered the following WRAS approved products for use in the construction. SAFELEASE – an environmentally safe, non-toxic, WRAS approved and highly…read more
Additional information
| Size (available in) | 5l, 20l, 25l, 205l, IBC |
|---|---|
| Coverage | 30-40m2 per litre |
| Certified | Eco, Safe, WRAS |
Related products
-
Plastrip S
Read More +Maximum Concentration, Low-Medium Viscosity, Mould Release Oil
Plastrip S is a chemical release agent specifically formulated to give easy release of plastic and thermoplastic mould liners, providing a high quality surface finish, but is suitable for all types of formwork.
It is easily applied and may be applied to formwork immediately prior to casting without reducing the finished quality.
Plastrip S will also offer corrosion protection to any metal surface.biodegradable and non-staining product that facilitates easy formwork release giving a very high quality surface finish.
Size (available in) - 5l
- 20l
- 25l
- 205l
- IBC
Coverage 30-40m2 per litre Certified - Eco
- Safe
-
Safestrike
Read More +Maximum Concentration, Mould Release Agent
Safestrike is a blend of natural vegetable oils designed for general site and precast use.
A high concentration release oil that is easily applied and is suitable for all types of formwork, even on sealed or unsealed timber in all climatic conditions.
Highly resistant to removal by rain showers or foot traffic.
It is particularly suited for white or fair faced concrete finishes.
Safestrike is a safe, environmentally friendly, readily biodegradable and non-staining product that facilitates easy formwork release.
Size (available in) - 5l
- 20l
- 25l
- 205l
- IBC
Coverage 30-40m2 per litre Certified - Eco
- Safe
-
Adoseal
Read More +Polyurethane Based Formwork Face / Surface Sealer
Adoseal is a low viscosity, low VOC, easy to use high solids, single pack moisture cured polyurethane coating.
Designed to impart a high quality, fully impervious surface lacquer finish to formwork and other porous surfaces.
This tough flexible sealing coating increases formwork life considerably. It improves concrete appearance by preventing staining from wood faced formwork.
It also improves formwork release and helps cut back on formwork cleaning time. It is easily applied by spray or brush and touch dries very quickly.
Size (available in) - 5l
- 20l
- 25l
- 205l
- IBC
Coverage 7-9m2 per litre